Tag Archives: Switch

Manage Your Brocade Fibre Channel Switch with recent Java & browser versions

Posted on by
31

Introduction

I was in the process of setting up a new jump server a management station server virtual machine on Windows Server 2016 Hyper-V. The guest was also Windows Server 2016 (desktop install). That station needed to be used to manage some aging Brocade fibre channel switches. With the default setting and links this will give you some headaches and some solution require you to keep older and insecure browser or java versions installed. We’ll show you how to get GUI access to your FC switches without needing to do that so you can manage your Brocade Fibre channel switch with recent Java & browser versions. Well not all of them, but it can be done with IE 11 and Firefox 52.0.1 (at the time of writing).

Another solution is to use the CLI naturally.

Manage Your Brocade Fibre Channel Switch with recent Java & browser versions

It’s OK to use the most recent Java version available. At the moment that I wrote this blog post that was Java 1.8.0.121. I can’t give guarantees other than that, but for now that does work.

Instead of navigating to http or https to just the IP address which will send you to https://x.x..x.x/switchexplorer you need to create a shortcut link to the following: https://10.30.2.2/switchexplorer_installed.html (or http://10.30.2.2/switchexplorer_installed.html if you have not enabled https on your switch).

Like this:

clip_image001

I normally change the icon to the shortcut to indicate it’s pointing to a network device. I actually created some ico files based on an image of brocades Fibre Channel switches that I use for this. I just place then under C:\Programdata\BrocadeFC for safe keeping together with a cop of the short cuts. On the management station, I add them to the desktop for easy access. Below is a screenshot of my Windows 10 or Windows Server 2016 (Desktop Experience) management station.

clip_image002

But we’re not there yet. You need to go to Java configuration and select the Security Tab. Make sure Enable Java Content in the browser is enabled. Leave the security at high but don’t forget to add the IP addresses of your Brocade switch to the Exception Site List.

clip_image004

You’ll need to add http or https or both depending on your situation. I think we can all agree we should go for https in this day and age.

In Firefox when you launch the shortcut you’ll get asked what app to use for opening this file.

clip_image005

Make sure you point it to javaws.exe (in C:\Program Files (x86)\Java\jre1.8.0_121\bin) if that’s not the case.

clip_image007Also, check to “Do this automatically for files like this from now on” for faster access during normal operations.

In Internet Explorer allow the add-on “Java SE Runtime Environment 8 Update 121 from Oracle America Inc.” to run.

clip_image009

When it comes to Chrome, this doesn’t’ work anymore. See https://www.java.com/en/download/faq/chrome.xml

When the application is launched, depending on the age of the fibre channel switch and the version of the firmware you’ll be greeted by a more or less harsh security warning.

clip_image010

clip_image011

Check the “I accept the risk and want to run this application” or “Do not show this again for this app from the publisher above” depending on the case. This also allows for easy access the next time you launch the shortcut. The app will launch and you’ll be greeted by the login screen.

clip_image012

Juts log in and there’s nothing more to it. You can now manage your FC switches from Firefox again.

image

Hope this helps some of you out there that come across this issue.

Upgrade the firmware on a Brocade Fibre Channel Switch

Posted on by
3

NOTE: content available as pdf download here.

Upgrade the firmware on a Brocade Fibre Channel Switch

In order to maintain a secure, well-functioning fibre channel fabric over the years you’ll need to perform a firmware upgrade now and again. Brocade fibre channel switches are expensive but they do deliver a very solid experience. This experience is also obvious in the firmware upgrade process. We’ll walk through this as a guide on how to upgrade the firmware on a Brocade fibre channel switch environment.

Have a FTP/SFTP/SCP server in place

If you have some switches in your environment you’re probably already running a TFTP or FTP server for upgrading those. For TFTP I use the free but simple and good one provided by Solarwinds. They also offer a free SCP/SFTP solution. For FTP it depends either we have IIS with FTP (and FTPS) set up or we use FileZilla FTP Server which also offers SFTP and FTPS. In any case this is not a blog about these solutions. If you’re responsible for keeping network gear in tip top shape you should this little piece of infrastructure set up for both downloads and uploads of configurations (backup/restore), firmware and boot code. If you don’t have this, it’s about time you set one up sport! A virtual machine will do just fine and we back it up as well as we store our firmware and backups on that VM as well. For mobile scenarios I just keep TFTP & FilleZilla Server installed and ready to go on my laptop in a stopped state until I need ‘m.

Getting the correct Fabric OS firmware

It’s up to your SAN & switch vendors to inform you about support for firmware releases. Some OEMs will publish those on their own support sites some will coordinate with Brocade to deliver them as download for specific models sold and supported by them. Dell does this. To get it select your switch version on the dell support site and under downloads you’ll find a link.

clip_image002

That link takes you to the Brocade download page for DELL customers.

clip_image004

Make sure you download the correct firmware for your switch. Read the release notes and make sure you’re the hardware you use is supported. Do your homework, go through the Brocade Fabric OS (FOS) 7.x Compatibility Matrix. There is no reason to shoot yourself in the foot when this can be avoided. I always contact DELL Compellent CoPilot support to verify the version is support with the Compellent Storage Center firmware.

When you have downloaded the firmware for your operating system (I’m on Windows) unzip it and place the content of the resulting folder in your FTP root or desired folder. I tend to put the active firmware under the root and archive older one as they get replaced. So that root looks like this. You can copy it there over RDP or via a FTP client. If the FTP server is running your laptop, it’s just a local copy.

clip_image005

The upgrade process

A word on upgrading the firmware

I you move from a single major level/version to the next or upgrade within a single major level/version you can do non-disruptive upgrades with a High Availability (HA) reboot meaning that while the switch reloads it will not impact the data flow, the FC ports stay online. Everything keeps running, bar that you lose connectivity to the switch console for a short time.

Some non-disruptive upgrade examples:

V6.3.2e to V6.4.3g

V7.4.0a to v7.4.0b

V7.3.0c to v7.4.0b

Note that this way you can step from and old version to a new one step by step without ever needing downtime. I have always found this a really cool capability.

You can find Brocades recommendations on what the desired version of a major release is in https://www.brocade.com/content/dam/common/documents/content-types/target-path-selection-guide/brocade-fos-target-path.pdf

I tend to way a bit with the latest as the newer ones need some wrinkles taken care of as we can see now switch 7.4.1 which is susceptible to memory leaks.

Some disruptive upgrade examples (FC ports go down):

7.1.2b to 7.4.0a

6.4.3.h to 7.4.0b

Our upgrade here from 7.4.0a to 7.4.0b is non-disruptive as was the upgrade from to 7.3.0c to 7.4.0a. You can jump between version more than one version but it will require a reboot that takes the switch out of action. Not a huge issue if you have (and you should) to redundant fabrics but it can be avoided by moving between versions one at the time. IT takes longer but it’s totally non-disruptive which I consider a good thing in production. I reserve disruptive upgrades for green field scenarios or new switches that will be added to the fabric after I’m done upgrading.

Prior to the upgrade

There is no need to run a copy run or write memory on a brocade FC switch. It persists what you do and you have to save and activate your zoning configuration anyway when you configure those (cfgsave). All other changes are persisted automatically. So in that regards you should be all good to go.

Make a backup copy of your configuration as is. This gives you a way out if the shit hits the fan and you need to restore to a switch you had to reset or so. Don’t forget to do this for the switches in both fabrics, which normally you have in production!

You log on switch with your username and password over telnet or ssh (I use putty or kitty)

MySwitchName:admin> configupload

Hit ENTER

Select the protocol of the backup target server you are using

Protocol (scp, ftp, sftp, local) [ftp]: ftp

Hit ENTER

Server Name or IP Address [host]: 10.1.1.12

HIT ENTER

Enter the user, here I’m using anonymous

User Name [user]: anonymous

Hit ENTER

Give the backup file a clear and identifying name

Path/Filename [<home dir>/config.txt]: MySwitchNameConfig20151208.txt

Hit ENTER

Select all (default)

Section (all|chassis|switch [all]): all

configUpload complete: All selected config parameters are uploaded

That’s it. You can verify you have a readable backup file on your FTP server now.

clip_image007

The Upgrade

A production environment normally has 2 fabrics for redundancy. Each fabric exists out of 1 or more switches. It’s wise to start with one fabric and complete the upgrade there. Only after all is proven well there should you move on to the second fabric. To avoid any impact on production I tend plan these early or late in the day also avoiding any backup activity. Depending on your environment you could see some connectivity drops on any FC-IP links (remote SAN replication FC to IP ó IP to FC) but when you work one fabric at the time you can mitigate this during production hours via redundancy.

Log on to first brocade fabric switch with your username and password over telnet or ssh (I use putty or kitty). At the console prompt type

firmwaredownload

This is the command for the non-disruptive upgrade. If you need or want to do a disruptive one, you’ll need to use firmwaredownload –s.

Hit Enter

Enter the IP address of the FTP server (of the name if you have name resolution set up and working)

Server Name or IP address: 10.1.1.12

User name: I fill out anonymous as this gives me the best results. Leaving it blank doesn’t always work depending on your FTP server.

User Name: anonymous

Enter the path to the firmware, I placed the firmware folder in the root of the FTP server so that is

Path: /v7.4.0b

Hit enter

At the password prompt leave the password empty. Anonymous FTP doesn’t need one.

Password:

Hit enter, the upgrade process preparation starts. After the checks have passed you’ll be asked if you want to continue. We enter Y for yes and hit Enter. The firmware download starts and you’ll see lost of packages being downloaded. Just let it run.

clip_image009

This goes on for a while. At one point you’ll see the prom update happening.clip_image011

When it’s done it starts removing unneeded files and when done it will inform you that the download is done and the HA rebooting starts. HA stands for high availability. Basically it fails over to the next CP (Control Processor, see http://www.brocade.com/content/html/en/software-upgrade-guide/FOS_740_UPGRADE/GUID-20EC78ED-FA91-4CA6-9044-E6700F4A5DA1.html) while the other one reboots and loads the new firmware. All this happens while data traffic keeps flowing through the switch. Pretty neat.

When you keep a continuous ping to the FC switch running during the HA reboot you’ll see a short drop in connectivity.

image

But do realize that since this is a HA reboot the data traffic is not interrupted at all. When you get connectivity back you SSH to switch and verify the reported version, which here is now 7.4.0b.

clip_image014

That’s it. Move on to the switch in the same fabric until you’re done. But stop there before you move on to your second fabric (failure domain). It pays to go slow with firmware upgrades in an existing environment.

This doesn’t just mean waiting a while before installing the very latest firmware to see whether any issues pop up in the forums. It also means you should upgrade one fabric at the time and evaluate the effects. If no problems arise, you can move on with the second fabric. By doing so you will always have a functional fabric even if you need to bring down the other one in order to resolve an issue.

On the other hand, don’t leave fabrics unattended for years. Even if you have no functional issues, bugs are getting fixed and perhaps more importantly security issues are addressed as well as browser and Java issues for GUI management. I do wish that the 6.4.x series of the firmware got an update in order for it to work well with Java 8.x.

Configuring timestamps in logs on DELL Force10 switches

Posted on by
Reply

When you get your Force10 switches up and running and are about to configure them you might notice that, when looking at the logs, the default timestamp is the time passed since the switch booted. During configuration looking at the logs can very handy in seeing what’s going on as a result of your changes. When you’re purposely testing it’s not too hard to see what events you need to look at. When you’re working on stuff or trouble shooting after the fact things get tedious to match up. So one thing I like to do is set the time stamp to reflect the date and time.

This is done by setting timestamps for the logs to datetime in configuration mode. By default it uses uptime. This logs the events in time passed since the switch started in weeks, days and hours.

service timestamps [log | debug] [datetime [localtime] [msec] [show-timezone] | uptime]

I use: service timestamps log datetime localtime msec show-timezone

F10>en
Password:
F10#conf
F10(conf)#service timestamps log datetime localtime msec show-timezone
F10(conf)#exit

Don’t worry if you see $ sign appear left or right of your line like this:

F10(conf)##$ timestamps log datetime localtime msec show-timezone

it’s just that the line is to long and your prompt is scrolling Winking smile.

This gives me the detailed information I want to see. Opting to display the time zone and helps me correlate the events to other events and times on different equipment that might not have the time zone set (you don’t always control this and perhaps it can’t be configured on some devices).

image

As you can see the logging is now very detailed (purple). The logs on this switch were last cleared before I added these timestamps instead op the uptime to the logs. This is evident form the entry for last logging  buffer cleared: 3w6d12h (green).

Voila, that’s how we get to see the times in your logs which is a bit handier if you need to correlate them to other events.