Windows NLB On Windows Server 2012 R2 Hyper-V: A Personal Preferred Configuration Using IGMP With Multicast

To know and see the issues we are dealing with in this demo, you need to read this blog post first: Windows NLB Nodes “Misconfigured” after Simultaneous Live Migration on Windows Server 2012 (R2).

We were dealing with some issues on on several WNLB clusters running on a Windows Server 2012 R2 Hyper-V cluster after a migration from an older cluster. So go read that and come back Smile.

Are you back? Good.

Let’s look at the situation we’ll use to show case one possible solution to the issues. If you have  a 2 node Hyper-V cluster, are using NIC Teaming for the switch and depending on how teaming is set up you’ll might run into these issues. Here we’ll use a single switch to mimic a stacked one (the model available to me is non stackable and I have only one anyway).

  • Make sure you enable MAC Spoofing on the appropriate vNIC or vNICs in the advanced settings


  • Note that there is no need to use a static MAC address or copy your VIP mac into the settings of your VM  with Windows Server 2012 (R2) Hyper-V
  • Set up WNLB with IGMP multicast as option. While chancing this there will be some advice warnings thrown at you Smile



I’m not going in to the fact that since W2K8 the network default configurations are all about security. You might have to do some configuration work to get the network flow to do what it needs to do. Lots on this  weak host/strong host model behavior on the internet . Even wild messy ramblings by myself here.

On to the switch itself!

Why IGMP multicast? Unicast isn’t the best option and multicast might not cut it or be the best option for your environment and IGMP is less talked about yet it’s a nice solution with Windows NLB, bar replacing into with a hardware load balancer. For this demo I have a DELL PowerConnect 5424 at my disposal. Great little switch, many of them are still serving us well after 6 years on the job.

What MAC address do I feed my switch configurations?

Ah! You are a smart cookie, aren’t you. A mere ipconfig reveals only the unicast MAC address of the NIC. The GUI on WNLB shows you the MAC address of the VIP. Is that the correct one for my chosen option, unicast, multicast or IGMP multicast?  No worries, the GUI indeed shows the one you need based on the WNLB option you configure. Also, take a peak at nlb.exe /? and you’ll find a very useful option called ip2mac.

Let’s run that against our VIP:


And compare it to what we see in the GUI, you’ll notice that show the MAC to use with IGMP multicast as well.


You might want to get the MAC address before you configure WNLB from unicast to IGMP multicast. That’s where the ip2mac option comes in handy.

Configuring your switch(es)

We have a multicast IP address that we’ll convert into the one we need to use. Most switches like the PowerConnect 5424 in the example will do that for you by the way.

I’m not letting the joining of the members to the Bridge Multicast Group happen automatically so I need to configure this. I actually have to VLANs, each Hyper-V host has 2 LACP NIC team with Dynamic load balancing connected to an LACP LAGs on this switch (it’s a demo, yes, I know no switch redundancy).  I have tow as some WNLB nodes have multiple clusters and some of these are on another VLAN.

I create a Bridge Multicast Group. For this I need the VLAN, the IGMP multicast MAC address and cluster IP address

When I specify the IGMP multicast MAC I take care to format it correctly with “:” instead of “–“ or similar.

You can type in the VIP IP address or convert is per this KB yourself. If you don’t the switch will sort you out.

The address range of the multicast group that is used is 239.255.x.y, where x.y corresponds to the last two octets of the Network Load Balancing virtual IP address.

For us this means that our VIP of becomes The switch handles typing in either the VIP or the converted VIP equally well.


This is what is looks like, here there are two WNLB clusters in ICMP multicast mode configured. There are more on the other VLAN.


We leave Bridge Multicast Forwarding here for what it is, no need in this small setup. Same for IGMP Snooping. It’s enable globally and we’ve set the members statically.

We make unregistered multicast is set to forwarding (default).


Basically, we’re good to go now. Looking at the counters of the interfaces & LAGs you should see that the multicast traffic is targeted at the members of the LAGs/LAGs and not all interfaces of the switch. The difference should be clear when you compare the counters adding up before and after you configured IGMP.


The Results

No over the top switch flooding, I can simultaneously live migrate multiple WLNB nodes and have them land on the same switch without duplicate IP address warning. Will this work for you. I don’t know. There are some many permutations that I can’t tell you what you should do in your particular situation to make it work well. I’ll just quote myself from my previous blog post on this subject:

“"If you insist you want my support on this I’ll charge a least a thousand Euro per hour, effort based only. Really. And chances are I’ll spend 10 hours on it for you. Which means you could have bought 2 (redundancy) KEMP hardware NLB appliances and still have money left to fly business class to the USA and tour some national parks. Get the message?”

But you have seen some examples on how to address issues & get a decent configuration to keep WNLB humming along for a few more years. I really hope it helps out some of you struggling with it.

Wait, you forgot the duplicate IP Address Warning!

No, I didn’t. We’ll address that here. There are some causes for this:

  • There is a duplicate IP address. If so, you need to address this.
  • A duplicate IP address warning is to be expected when you switch between unicast and multicast NLB cluster modes ( Follow the advice in the KB article and clearing the ARP tables on the switches can help and you should get rid of it, it’s transient.
  • There are other cause that are described here Troubleshooting Network Load Balancing Clusters. All come down to the fact that somehow you’re getting multiple MAC address associated with the same IP address. One possible cause can be that you migrated form an old cluster to a new cluster, meaning that the pool of dynamic IP addresses is different and hence the generated VIP MAC … aha!
  • Another reason, and again associated multiple MAC address associated with the same IP address is that you have an old static ARP entry for that IP address somewhere on your switches. Do some house cleaning.
  • If all the above is perfectly fine and you’re certain this is due to some Hyper-V live migration, vSwitch, firmware, driver bug you can get rid of the warning by disabling ARP checks on the cluster members. Under HKLMSYSTEMCurrentControlSetServicesTcpipParameters, create a DWORD value with as name “ArpRetryCount” and set the value to 0. Reboot the server for this to take effect. In general this is not a great idea to do. But if you manage your IP addresses well and are sure no static entries are set on the switch it can help avoid this issue. But please, don’t just disable “ArpRetryCount” and ignore the root causes.


You can still get WNLB to work for you properly, even today in 2014. But it’s time to start saying goodbye to Windows NLB. The way the advanced networking features are moving towards layer 3 means that “useful hacks” like MAC spoofing for Windows NLB are going no longer going to work.  But until you have implement hardware load balancing I hope this blog has given you some ideas & tips to keep Windows NLB running smoothly for now. I’ve done quite few and while it takes some detective work & testing, so far I have come out victorious. Eat that Windows NLB! I have always enjoyed making it work where people said it couldn’t be done. But with the growing important of network virtualization and layer 3 in our networks, this nice hack, has had it’s time.

For some reasons developers like Windows NLB as  “it’s easy and they are in control as it runs on their servers”. Well … as you have seen nothing comes free and perhaps our time is better spend in some advanced health checking and failover in hardware load balancing. DevOps anyone?

Windows NLB Nodes Misconfigured after Simultaneous Live Migration on Windows Server 2012 (R2)

Here’s the deal. While Windows NLB on Hyper-V guests might seem to work OK you can run into issues. Our biggest challenge was to keep the WNLB cluster functional when all or multiple node of the cluster are live migrated simultaneously. The live migration goes blazingly fast via SMB over RDMA nut afterwards we have a node or nodes in an problematic state and clients being send to them are having connectivity issues.

After live migrating multiple or all nodes of the Windows NLB cluster simultaneously the cluster ends up in this state:


A misconfigured interface. If you click on the error for details you’ll see


Not good, and no we did not add those IP addresses manually or so, we let the WNLB cluster handle that as it’s supposed to do. We saw this with both fixed MAC addresses (old school WNLB configuration of early Hyper-V deployments) and with dynamic MAC addresses. On all the nodes MAC spoofing is enabled on the appropriate vNICs.

The temporary fix is rather easy. However it’s a manual intervention and as such not a good solution. Open up the properties of the offending node or nodes (for every NLB cluster that running on that node, you might have multiple).


Click “OK” to close it …


… and you’re back in business.



Scripting this out somehow with nlb.exe or PowerShell after a guest gets live migrated is not the way to go either.

But that’s not all. In some case you’ll get an extra error you can ignore if it’s not due to a real duplicate IP address on your network:


We tried rebooting the guest, dumping and recreating the WNLB cluster configuration from scratch. Clearing the switches ARP tables. Nothing gave us a solid result.

No you might say, Who live migrates multiple WNLB nodes at the same time? Well any two node Hyper-V cluster that uses Cluster Aware Updating get’s into this situation and possibly bigger clusters as well when anti affinity is not configured or chose to keep guest on line over enforcing said anti affinity, during a drain for an intervention on a cluster perhaps etc. It happens. Now whether you’ll hit this issue depends on how you configure and use your switches and what configuration of LBFO you use for the vSwitches in Hyper-V.

How do we fix this?

First we need some back ground and there is way to much for one blog actually. So many permutations of vendors, switches, configurations, firmware & drivers …


This is the default and Thomas Shinder has an aging but  great blog post on how it works and what the challenges are here. Read it. It you least good option and if you can you shouldn’t use it. With Hyper-V we and the inner workings and challenges of a vSwitch to the mix. Basically in virtualization Unicast is the least good option. Only use it if your network team won’t do it and you can’t get to the switch yourself. Or when the switch doesn’t support mapping a unicast IP to a multicast MAC address. Some tips if you want to use it:

  1. Don’t use NIC teaming for the virtual switch.
  2. If you do use NIC teaming for the virtual switch you should (must):
    • use switch independent teaming on two different switches.
    • If you have a stack or just one switch use multicast or even better IGMP with multicast to avoid issues.

I know, don’t shout at me, teaming on the same switch, but it does happen. At least it protects against NIC issues which are more common than switch or switch port failures.


Again, read Thomas Shinder his great blog post on how it works and what the challenges are here.

It’s an OK option but I’ll only use it if I have a switch where I can’t do IGMP and even then I do hope I can do two things:

  1. Add a static entry for the cluster IP address  / MAC address on your switch if it doesn’t support IGMP multicast:
    • arp [ip] [cluster multicast mac*] ARPA  > arp  03bf.bc1f.0164 ARPA
  2. To prevent switch flooding occurs, as with the unicast configure your switch which ports to use for multicast traffic:
    • mac-address-table static [cluster multicast mac] [vlan id] [interface]  > mac-address-table static 03bf.bc1f.0164 vlan 10 interface Gi1/0/1

The big rotten thing here is that this is great when you’re dealing with physical servers. They don’t tend to jump form switch port to switch port and switch to switch on the fly like a virtual machine live migrating. You just can’t hardcode all the vSwitch ports into the physical switches, one they move and depending on the teaming choice there are multiple ports, switches etc …it’s not allowed and not possible. So when using multicast in a Hyper-V environment stick to 1). But here’s an interesting fact. Many switches that don’t support 1) do support 2). Fun fact is that most commodity switches do seems to support IGMP … and that’s your best choice anyway! Some high end switches don’t support WNLB well but in that category a hardware load balancer shouldn’t be an issue. But let’s move on to my preferred option.

  • IGMP With Multicast (see IGMP Support for Network Load Balancing)

    This is your best option and even on older, commodity switches like a DELL PowerConnect 5424 or 5448 you can configure this. It was introduced in Windows Server 2003 (did not exist in NT4.0 or W2K). It’s my favorite (well, I’d rather use hardware load balancing) in a virtual environment. It works well with live migration, prevents switch flooding and with some ingenuity and good management we can get rid of other quirks.

    So Didier, tell us, how to we get our cookie and eat it to?

    Well, I will share the IGMP with Multicast solution with you in a next blog. Do note that as stated above there are some many permutations of Windows, teaming, WNL, switches  & firmware/drivers out there I give no support and no guarantees. Also, I want to avoid writing a  100 white paper on this subject?. If you insist you want my support on this I’ll charge at least a thousand Euro per hour, effort based only. Really. And chances are I’ll spend 10 hours on it for you. Which means you could have bought 2 (redundancy) KEMP hardware NLB appliances and still have money left to fly business class to the USA and tour some national parks. Get the message?

    But don’t be sad. In the next blog we’ll discuss some NIC teaming for the vSwitch, NLB configuration with IGMP with Multicast and show you a simple DELL PowerConnect 5424 switch example that make WNLB work on a W2K12R2 Hyper-V cluster with NIC teaming for the vSwitch and avoids following issues:

    • Messed up WNLB configuration after the simultaneous live migration of all or multiple NLB Nodes.
    • You avoid “false” duplicate IP address goof ups (at the cost of  IP address hygiene management).
    • You prevent switch port flooding.

    I’d show you on redundant Force10 S4810 but for that I need someone to ship me some of those with SFP+ modules for the lab, free of cost for me to keep Winking smile


    It’s time to start saying goodbye to Windows NLB. The way the advanced networking features are moving towards layer 3 means that “useful hacks” like MAC spoofing for Windows NLB are going no longer going to work.  But until you have implement hardware load balancing I hope this blog has given you some ideas & tips to keep Windows NLB running smoothly for now. I’ve done quite few and while it takes some detective work & testing, so far I have come out victorious. Eat that Windows NLB!

  • E2EVC 2014 Brussels

    Ladies & gentleman, on May 30-June 1, 2014 the E2EVC 2014 Brussels Virtualization Conference is taking place. This is a non marketing event by experts in virtualization. So these people design, implement and support virtualization solutions for a living.  E2EVC Virtualization Conference is a non-commercial, it does not run a profit for the organizers or speakers. Everybody volunteers. The attendance fee covers the costs of the conference rooms, coffee breaks and such. The value is in the knowledge sharing and the networking.

    This community event strives to bring the best virtualisation experts together to exchange knowledge and to establish new connections. It’s a weekend event (so people can attend without interrupting their work or customer services. Filled with presentations, Master Classes and discussions you can have 3 days to network and learn from your peers.

    So the next event will take place in Brussels, Belgium May 30 – June 1, 2014 in Hotel Novotel Brussels Centre Tour Noire. So my Belgian colleagues, this is your change to be al little Dutch as they have a SPECIAL PRICE FOR BELGIAN RESIDENTS – 199 EUR!

    If you’re not Belgian you are also very welcome. So do register for E2EVC 2014 Brussels. If you have knowledge to share, please volunteer to speak. This community event has as a goal to share knowledge and stimulates professionals to present on their subject matters.

    A big thank you for Alex Juschin & team for his never ending efforts to help organize this conference!

    vKernel Adds Tools to Free vOPS Server Explorer 6.3

    When it comes to gaining insight and understanding of your virtual environment vKernel has some nifty products. They just added two new utilities, Storage Explorer and Change Explorer, to their free vOPS™ Server Explorer that give you more management capabilities with SCOM/SCVMM or vCenter. Sure it’s to get you looking into and considering buying the paid stuff with more functionality and remediation but it does provide you with tools to rapidly asses your virtualization environment for free as is. So what did they add?

    Storage Explorer

    • Gain insight into storage performance and capacity via views across data stores and VMs
    • Identifies critical storage issues such as over commitment, low capacity, high latency, VMFS version mismatch
    • Alerts you to critical VM issues such as low disk space,  latency and throughput issues
    • There’s sorting and searching support

    Change Explorer

    • You get a listing of the changes to resource pools, hosts, data stores and VMs within the past week. They also indicate a risk associated with hat change
    • You can search & filter to find specific changes
      • There is a graphical mapping of changes over a time line for rapid reporting/assessment.
      • So if you need some free tools to help you get a quick insight into your environment or the need to be informed about changes of performance issues you can try these out. The press release is here We have smaller environment at work next to our main production infrastructure where we’d like to test this out. So they need to add support for SCVMM 2012 SP1 a.s.a.p. I think Smile

        In a world were complexity reduction is paramount and the TCO/ROI needs to be good from day one competition is heating up between 3rd party vendors active in this arena providing tools to make that happen. This is especially true when they are adding more and more Hyper-V support. It also doesn’t hurt to push Microsoft or VMware to make their solutions better.